1. Manuals
  2. Consumer Electronics Support
  3. Whirlpool Support
  4. Dishwasher Support
Support User Manuals
Question About Whirlpool Dishwasher adp6000ix
error 4 code...

error code 4 comes up and no washing can proceed what do i do

Asked by amanda on 05/14/2008 46  Answers

ManualsOnline posted an answer 16 years, 6 months ago

The ManualsOnline team has found the manual for this product! We hope it helps solve your problem. Get the Manual Here

James posted an answer 12 years, 2 months ago

6 Just fixed Err 4 by pulling the machine out, tipping it over onto its left hand side at 45 degrees, emptying lots of water then standing back up again & heh presto, it's now OK again !!
Was this answer helpful?

Sean posted an answer 12 years, 3 months ago

4 we pulled it out.. undid the water, power and drain.. shook it sideways.. lots of water spilled out - this was a good thing.. plugged it all up and it started working... Oh Error 1 means you need to buy a completely new water hose from our experience (ours came broken)
Was this answer helpful?

GAVIN posted an answer 16 years ago

3 I have the same problem but with Err6!! It's bloody annoying, wont wash any dishes and just keeps beeping!
Was this answer helpful?

Steve posted an answer 15 years, 7 months ago

3 Was just looking for the answer to the same problem and found my manual. Error Code 4 means: Overfilled - Too much inlet water. I found by disconnecting the water supply (after turning it off) then reconnecting it fixed it
Was this answer helpful?

Amy posted an answer 13 years, 12 months ago

3 Just checked my manual.. the following may be useful: Err1- Longer inlet time- Faucets is not opened Err2- Longer draining time- Installation of drain pipe is too high Err3- Longer heating time, but not reaching required temp- malfunction of temp sensor or heating element Err4- Overfilled- Too much inlet water Err6, Err7- Abnormal temp- Short circuit or break of temp sensor
Was this answer helpful?

Cherie posted an answer 14 years, 7 months ago

3 i moved into a new house with this dishwasher that is brand new. it had been tested with the first wash by the real estate agent. now when i go to use it ERR 1 with loads of beeping. no water goes in! any ideas? they didnt leave us the manual!
Was this answer helpful?

sir posted an answer 14 years, 5 months ago

3 i have err4. and am trying to find out what caused it. err4 is an overfill as mentioned above, but what it is is that there is water in the bottom of the dishwasher externally,,, as in where the pumps are, there is a float in there that stops the dishwasher so that it doesn't short out the electronics. the problem is that there is no suction to get it out. I took the side cover off and got in there with a cooking syringe and sucked it out, i got over 2 cups of water out.
Was this answer helpful?

deb posted an answer 16 years, 3 months ago

2 i have the same error 2 hope there is someone out there whirlpool are no help just get flogged off
Was this answer helpful?

Grant posted an answer 13 years, 2 months ago

2 Err4 water in drain tray remove back panel and dry it out fixes the fault
Was this answer helpful?

Chantel posted an answer 16 years, 5 months ago

1 I have the same error. Error 4 on Whirlpool dishwasher ADP 6000ix. Any suggestions on what it is
Was this answer helpful?

Dan posted an answer 15 years, 1 month ago

1 No, i tried turning it off and disconnecting the water supply, then reconnecting it and it still gives me the error
Was this answer helpful?

P R Stephenson posted an answer 10 years, 8 months ago

0 Just had same problem so I turned off water supply and undid the water inlet hose, drained excess water and reconnected the hose. Now all good again. :)
Was this answer helpful?

Stuart posted an answer 10 years ago

0 I had this problem and what I found was there is a switch attached to the bottom panel that is activated by a foam float, which had got stuck in the up position for me. Its real easy to access if you lay your dishwasher on its back I sorted that problem but then found water was getting to that switch from water leaking past the door seal and draining through two small tubes at the base of the door. If you have any leaks and water is getting down to this switch it is going to keep having an Err fault. You can drain the water away and it will work again but only for the short term.
Was this answer helpful?

Add Your Answer

Please Note: Do not submit personal information as it will be displayed online.
Ask a Question Request a Manual