Operation Guide 5219 (OC)
E-23
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time setting manually
Pull out the crown.1.
This will cause the
x
Second Hand to move to the city code of the
currently selected Home City.
If you do not perform any operation with the crown for about two minutes
x
after pulling it out, crown operations will become disabled and the hand
will not move if you rotate the crown. If this happens, push the crown
back in and then pull it out again.
Change the Home City setting, if you want.2.
To change the Home City setting, perform step 2 under “To confi gure
x
Home City Settings” (page E-20).
Hold down 3. B for about two seconds. This will enter the time setting mode.
The
x
Second Hand will move to the 12 o’clock.
In the following steps, each press of
x B cycles between settings as shown
below.
TOKYO (TYO)
E-22
To switch between standard time and summer time manually
Perform steps 1 and 2 under “To confi gure Home City settings” 1.
(page E-20).
Selecting a city code will cause the
x
Hour Hand,
Minute
Hand, and
Upper Dial Hand to move automatically to the
current time for the selected city code.
If you will use the watch in a city that is not included in the
x
city code list, select a city code that is in the same time zone
as your city.
Displaying the Home City Settings screen will cause the
x
short end of the
Lower Dial Hand to move to AUTO (auto
switching), STD (standard time manual setting), or DST
(summer time manual setting).
If
− STD or DST is indicated, go directly to step 3 of this
procedure.
If
− AUTO is indicated, proceed to step 2.
Hold down 2. A for about one second until the short end of the
Lower Dial Hand moves to MNL (manual), and then moves
to STD or DST.
If
− STD is indicated, the watch will always show standard time
If
− DST is indicated, the watch will always show summer time
Press 3. A to move the short end of the
Lower Dial Hand between STD and DST.
To switch from x STD or DST to AUTO, hold down A for about one second.
After the setting is way you want, push the crown back in.4.
Switching between AUTO and STD
(or DST)
Switching between STD and DST
A1 sec
A
E-21
STD/DST Switching
You can select summer time or standard time independently for each city. The initial default setting for all
cities is AUTO.
Normally you should use the AUTO setting because it automatically switches between summer time
and standard time. You should change the setting to STD (standard time) or DST (summer time) in the
following cases.
When using the watch in a city not included in the City Code Table
−
When the switching dates in your location are different from those shown in the City Code Table −
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time.
Remember that not all countries or even local areas use Daylight Saving Time.
Note that you cannot switch between
x STD (standard time) and DST (daylight saving time) while UTC*
is selected as your Home City.
Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The reference point for *
UTC is Greenwich, England.
E-20
Confi guring Home City Settings
The Home City is location where you will normally use the watch. You can choose from a selection of city
codes that represent 29 cities around the globe.
To confi gure Home City settings
Note
This watch does not have a city code that corresponds to Newfoundland.
x
Pull out the crown.1.
This will cause the x
Second Hand to move to the city code of the
currently selected Home City.
This indicates the city code setting mode.
x
If you do not perform any operation with the crown for about two x
minutes after pulling it out, crown operations will become disabled and
the hand will not move if you rotate the crown. If this happens, push the
crown back in and then pull it out again.
For details about city codes, see the “City Code Table” at the back of
x
this manual.
Rotate the crown to move the 2.
Second Hand to the city code you want
to select as your Home City.
Each time you select a city code, the
x
Hour Hand,
Minute Hand,
Lower Dial Hand and
Day move to the current time and date for
that city code.
Push the crown back in to return to the Timekeeping Mode.3.
TOKYO (TYO)
E-19
Timekeeping
To enter the Timekeeping Mode, hold down B at least two seconds.
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Upper Dial Hand: Indicates the current hour in the Home City time in
24-hour format.
b Lower Dial Hand: Indicates the current day of the week.
n Day
E-18
Mode Reference Guide
Your watch has two “modes”. The mode you should select depends on what you want to do.
To do this: Enter this mode: See:
View the current time in your Home City and in one of 29 other cities x
around the globe
View the current date in the Home City
x
Confi gure Home City and daylight saving time (DST) settings x
Perform a time calibration signal receive operation x
Confi gure time and date settings manually x
Timekeeping Mode E-19
Use the stopwatch to measure elapsed time Stopwatch Mode E-27
Timekeeping Mode
Stopwatch Mode
The hand indicates the day of the week
(SUN/MON/TUE/WED/THU/FRI/SAT).
Hand points to STW.
B
B(Stopwatch reset to 00:00 or running.)
Hold down
x B at least two seconds to enter the Timekeeping Mode.
E-17
Radio-controlled Atomic Timekeeping Precautions
Strong electrostatic charge can result in the wrong time setting.
x
Even if a receive operation is successful, certain conditions can cause the time setting to be off by up x
to one second.
The watch is designed to update the date and day of the week automatically for the period from
x
January 1, 2000 to December 31, 2099. Updating of the date by signal reception will no longer be
performed starting from January 1, 2100.
If you are in an area where signal reception is not possible, the watch keeps time with the precision
x
noted in “Specifi cations” (page E-36).
The receive operation is disabled under any of the following conditions.
x
While power is at Level 2 or lower (page E-8) −
While the watch is in the power recovery mode (page E-9) −
While the watch is in the function sleep state (power saving, page E-10) −
E-16
To check the result of the latest receive operation
In the Timekeeping Mode, press A.
The
x
Second Hand will move to YES (Y) if the latest receive operation
was successful, or NO (N) if it was not. After about ten seconds, regular
timekeeping will resume.
You can return to the Timekeeping Mode manually by pressing
x A while
the
Second Hand is pointing to YES (Y) or NO (N).
Note
The
x
Second Hand will indicate NO (N) if you have adjusted the time or
date setting manually since the latest receive operation.
To turn auto receive on and off
YES (Y)
NO (N)
In the Timekeeping Mode, press 1. A.
Pull out the crown.2.
The
x
Second Hand will perform one full revolution and then stop at
either YES (Y) or NO (N) to indicate the current on/off setting.
Rotate the crown to move the 3.
Second Hand to the setting you want.
To turn on auto receive, select x YES (Y).
To turn off auto receive, select x NO (N).
Push the crown back in to return to the Timekeeping Mode.4.
