.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
QUICKSPECS
11-28 DA-10307-01-001
Compaq NC6133
Gigabit Module
1000 LX
EASE OF USE
CPQNTAC
The CPQNTAC (Compaq Network Teaming and Configuration) utility allows the user to run initial diagnostics and
configure NIC teams for Network Fault Tolerance, Adaptive Load Balancing or Cisco Gigabit EtherChannel (when
used with a Gigabit EtherChannel-enabled switch)
Diagnostic LEDs
LEDs show link integrity and network activity at a glance for easy troubleshooting.
Compaq Total Solutions
The NC6133 provides a 1000 Mbps LX network connection between servers and the Compaq SW5411, SW5425,
SW5450 and the GIGAswitch/Router. By integrating these Compaq solutions throughout a network, users can apply
the complete set of Compaq management tools across their enterprise.
Warranty
1
Compaq supports this product with a limited lifetime warranty
1
. Technical support is available at your fingertips 24
hours a day, 7 days a week.
SPECIFICATIONS
Compliance IEEE 802.3z compliant 1000 Mbps Ethernet specification
PCI 2.1
General Specifications
Communications Processor
Intel 82542
Half and full duplex
On-board memory 64 KB
Data path
32 and 64-bit/33MHz
Interrupt levels INTC
Bus architecture PCI bus-mastering
Connectors
SC
Wavelength LX = (1,300nm)
Distance up to 5,000 meters
Wiring
Multi-mode fiber (62.5µm)
Dimensions (LxW) 6 x 2.5 in/15 x 6.4 cm
64-bit addresses for systems with more than 4 GB of physical memory
64-bit PCI host interface compliant with PCI 2.1
Command usage optimization for advanced PCI commands (MWI and memory reads)
Software controlled global reset bit (resets everything except PCI configuration registers)
Power and Environmental Specifications
Operating
Temperature 32° to 131°F/0° to 55°C
Humidity 10% to 90%
Non-operating
Temperature –85° to 185°F/–65° to 85°C
Humidity 5% to 95%
Power requirement 1025 mA @ 5V max
Emissions standards FCC Class B
Safety compliance CE Mark
