OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Crevice Tool and Dusting Brush
Note: Once all attachments are in
place, unwind a sufficient length
of cable and insert the plug into
the wall outlet. A yellow mark on
the power cord shows the ideal
cable length. Don't pull the power
cord beyond the red mark.
1. Insert the power plug into the wall
outlet.
2. Press the Power On/Off button
located on the unit to turn the
vacuum cleaner "On".
Using your Vacuum
Cord Rewind
Button
1. Crevice Tool with Brush
For radiators, crevices,
corners, baseboards and
between cushions.
2. Upholstery Brush
The dusting brush is used
for the furniture
5
3. To rewind the power cord, press the
cord rewind button with one hand
and hold the plug of the power cord
with the other hand to ensure that it
does not whip causing damage or
injury.
Top Rim
Stem
Warning: Always unplug the unit
from electrical outlet before
removing the Dust Cup (container).
Warning: After each Use - Always
remove the Rinseable "TapClean"
HEPA Filter from the Dust Cup, then
vigorously “TapClean” HEPA Filter until
no more dust can be removed.
Important: When "TapCleaning" the
HEPA filter, hold the HEPA filter from the
stem and tap ONLY the top rim against
the side of the waste container. NEVER
tap directly on the pleated folds of the
HEPA filter.
3. Hold dust cup container over a
waste basket (garbage can), push
the dust cup release button to
open the dust cup. Dispose of the
dust inside. (See illustration
below.)
Note: If dust is tightly packed and
difficult to remove, tap the side of
the dust cup lightly against the
side of the waste basket (garbage
can).
Press
5. After you have removed the
Rinseable "TapClean" HEPA dust
cup filter from the dust cup, separate
the debris screen from
the HEPA filter cartridge
by holding the top rim of
the filter and twisting the
debris screen
counterclockwise to unlock
the debris screen from the
filter. Then lift the debris
screen to remove.
6. Rinse the debris screen
under the faucet with
lukewarm water until
clean. Allow to air dry for 24 hours.
Do NOT wash in dishwasher.
Removing & Cleaning the
Rinseable "TapClean" HEPA
Dust Cup Filter
Motor Thermostat
1. Push the Power On/Off button to
"Off" and disconnect the power
cord from the wall outlet.
2. Lift the dust cup handle and lift the
dust cup container out.
Important: This vacuum cleaner is
equipped with a motor protective
thermostat. If for some reason your
vacuum overheats, the thermostat will
automatically turn the unit off. Should this
occur, unplug the vacuum from the wall
outlet and turn off the switch. Empty the
dust cup, "TapClean" the dust cup filter
and check for blockages in hose and
suction inlet. Allow the unit to cool for a
minimum of 45 minimum prior to
restarting the unit. To restart, re-plug the
vacuum into the wall socket and turn the
switch back on
Power On/Off
Button
IMPORTANT, Please Note: The
Rinseable “TapClean” HEPA Dust Cup
Filter will stop most of the tiniest dust
particles from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Dust Cup Filter
will quickly accumulate dirt inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA Filter as described in this section,
then reconnect unit and proceed with
vacuuming.)
4. After you have
emptied the dust
container, hold the
HEPA filter from the
stem and twist it
counter clockwise to
release it from the
dust cup container.
Open
6
