2001/2002-5
Equalizer Settings
You can use the Equalizer Screen to select one of five different equalizer
settings to produce the playback effect you want.
To make equalizer settings
1. Press the MODE button a number of times
until the Equalizer Screen appears.
• The Equalizer Screen appears when you
press the MODE button while in the Part
Loop Mode.
2. If you want to monitor the effects of your
equalizer setting, press
to start
playback.
3. Use
and to change the equalizer
setting.
• Changing the equalizer settings causes the
equalizer indicator to appear as shown
below.
4. After the setting is the way you want, press
the MODE button to exit the Equalizer
Screen and return to the Normal Mode.
Highest Range
Enhanced
High Range
Enhanced
Flat
Low Range
Enhanced
Lowest Range
Enhanced
02 5
38
02 0
10
Equalizer Screen
indicator
Equalizer indicator
TIMEKEEPING MODE
The Timekeeping Mode displays the current
time. This is the normal “home” mode of the
watch when playback is not being performed.
• Hold down
when you want to view the
current date. Releasing the button returns to
the current time display.
• Use the SETTING MODE to set the current
time and date.
Switching between Standard Time and Daylight
Saving Time
Daylight Saving Time (DST) automatically advances the time setting by one
hour from Standard Time. Whether you should use Daylight Saving Time
depends on the geographic area where you are currently located.
To select Daylight Saving Time
In the Timekeeping Mode, hold down for about two seconds to toggle
between Daylight Saving Time (DST displayed) and Standard Time (DST not
displayed).
Switching between 12-hour and 24-hour Timekeeping
Each press of in the Timekeeping Mode toggles between 12-hour and 24-
hour timekeeping.
The 12-hour/24-hour timekeeping format you select is applied in all modes.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour
digits for times in the range of noon to 11:59 p.m. There is no indicator for
times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are indicated in the range of 0:00 to 23:59,
with 24 indicator.
10 588
35
Hour : Minutes
Seconds
Day of week
ALARM MODE
You can set a Daily Alarm that sounds at the same time each day, while it is
turned on. You can also turn on an Hourly Time Signal that causes the watch
to beep twice every hour on the hour.
Note
• During Player Mode playback, the Daily Alarm and Hourly Time Signal
sound through the earphone.
• The volume level of the Daily Alarm, Hourly Time Signal cannot be
adjusted.
Setting the Alarm Time
1. In the Alarm Mode, press so that the
hour digits of the alarm time start to flash,
which indicates the setting screen.
• The hour digits are flashing because they
are selected.
• Each press of
moves the flashing around
the setting screen in the sequence shown
below.
2. While the hour setting is flashing, use to
change it.
• This operation automatically turns on the
Daily Alarm.
• Holding down
changes the setting at high
speed.
• When setting the alarm time using the 12-
hour format, take care to set the time
correctly as am (no indicator) or pm (P
indicator).
3. Press
so that the minute digits of the alarm time start to flash.
4. While the minute setting is flashing, use
to change it.
• Holding down
changes the setting at high speed.
5. Press
to exit the setting screen.
Hourly time
signal on indicator
Alarm time
(Hour : Minutes)
Alarm on indicator
Daily Alarm Operation
The alarm sounds at the preset time each day for about 20 seconds, or until
you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down to sound the alarm.
To turn the Daily Alarm and Hourly Time Signal on and off
In the Alarm Mode, press to cycle through the on and off settings as
shown below.
[Alarm ON Indicator / Hourly Time Signal ON Indicator]
Alarm On
Signal On
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
