To enable Auto-on, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until
“Auto-start” is displayed;
3. Press the button. “Enable?” is displayed;
4. Press the button to conrm;
5.
Press the
MILK or CAPPUCCINO
button to choose the
hours;
6. Press the button to conrm;
7. Press the MILK or CAPPUCCINO button (g. 8) to change
the minutes;
8. Press the button to conrm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been conrmed, enabling of auto-start is
indicated by the symbol displayed alongside the time
and under the Auto-start item in the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press the button. “Disable?” is displayed;
3. Press the button to conrm.
The symbol is no longer displayed.
Setting the temperature
To modify the temperature of the water used to make the
coee, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until “Set
temperature” is displayed;
3. Press the button;
4. Press the MILK or CAPPUCCINO button until the required
temperature (●= low, ●●●● = high) is displayed;
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) “energy saving” mode, proceed as
follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until
“Energy saving” is displayed;
3. Press the button. “Disable?” is displayed (or
“Enable?” if the function has been disabled);
4. Press the button to disable (or enable) energy
saving mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving” is displayed.
Please note!
When in energy saving mode, a few seconds may elapse before
the rst drink with milk is delivered as the appliance must heat
up again.
Cup warmer
This function enables or disables the cup warmer.
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until “Cup
warmer” is displayed;
3. Press the button. “Disable?” is displayed (or
“Enable?” if the function has been disabled);
4. Press the button to disable (or enable) the
function.
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coee hot.
Setting water hardness
For instructions on setting water hardness, see page 17.
Setting the language
To change the language for the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until “Set
language” is displayed;
3. Press the button;
4. Press the MILK or CAPPUCCINO button until the required
language is displayed;
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Install lter
For instructions on how to install the lter, see the section
“Installing the lter” on page 18.
Replacing the lter
For instructions on how to replace the lter, see the section
“Replacing the lter” on page 19.
Beep
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (g. 8) until
“Beep” is displayed;
3. Press the button. “ Disable?” or “ Enable?” is
