GB
21
GB
20
Clearing a Preset Station
If you have stored a TV station:
◆ That you do not require
◆ At the wrong programme position
you can cancel it.
1 Press the SETUP button on the remote control.
2 Press the corresponding
"
,
❷
buttons to select the VCR Setup
option.
3 Press the ENTER button to select this option.
4 Press the corresponding
"
,
❷
buttons to select the
Installation menu.
5 Press the ENTER button to select this menu.
Result
: The INSTALLATION menu is displayed.
6 Press the corresponding
"
or
❷
buttons, until the MANUAL SET
UP option is selected.
7 Press the ENTER button to select this option.
Result
: The TV STATION TABLE menu is displayed.
8 Press the corresponding
"
or
❷
buttons, until the required preset
TV station is selected. (
PR)
9 Press the CLEAR button.
10 Repeat the same procedure from Step 8 onwards until all the
required stations have been cleared.
11 On completion, press the RETURN button to exit the menu.
TV STATION TABLE
PR CH NAME
1 003
2
3
4
5
"❷
❿!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
SWAPPING:ENTER
RETURN DELETE:CLEAR
Presetting the Stations Manually
☛ You do not need to preset the stations manually if you
have already set them automatically.
1 Press the SETUP button on the remote control.
Result
: The MAIN MENU is displayed.
2 Press the corresponding
"
,
❷
buttons to select the VCR Setup
option.
3 Press the ENTER button to select this option.
4 Press the corresponding
"
,
❷
buttons to select the
Installation menu.
5 Press the ENTER button to select this menu.
Result
: The INSTALLATION menu is displayed.
6 Press the corresponding
"
or
❷
buttons, until the MANUAL SET
UP option is selected.
7 Press the ENTER button to select a MANUAL SET UP option.
Result
: The TV STATION TABLEmenu is displayed.
8 Press the
"
or
❷
buttons to select a programme number as
required.
9 Press the
❿!
button to preset the station.
Result
: The MANUAL TUNINGmenu is displayed.
10 Press the
➛
or
❿
buttons to start scanning.
Result
: The frequency band is scanned and the first station
found is displayed.
11 Press the
"
or
❷
buttons until the NAME is selected.
The station name is set automatically from the broadcast signal.
12 To change the programme’s name, press the
❿!
button.
Result
: The first letter of the name flashes.
13 To... Then...
Select a character Press the
"
or
❷
button until the
in the name required character is displayed
(letters, numbers or “-” character).
Move to the next or Press the
❿
or
➛
buttons
previous character respectively.
14 If you... Then...
Wish to store the ◆ Press the
"
or
❷!
buttons until the MFT
station displayed is selected.
◆ Press the
➛
or
❿
buttons to adjust the
picture, if necessary.
◆ Press ENTER to store the station
Do not
wish to
◆ Press the
"
or
❷
buttons until the
store the station
CH is selected.
displayed
◆ Press the
➛
or
❿
buttons to go on
scanning the frequency band and display
the next station
◆ Go back to the beginning of Step 14
15 Repeat this procedure from Step 8 onwards, until all the required
stations have been stored.
16 On completion, press the RETURN button to exit the menu.
☛ You do not need to preset the stations manually if you
have already set them automatically.
TV STATION TABLE
PR CH NAME
1
2
3
4
5
"❷
❿!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
SWAPPING:ENTER
RETURN DELETE:CLEAR
MANUAL TUNING
PR :
CH : ---
MFT : -
NAME : ----
"❷!!!
➛❿!!!
MEMORY:ENTER
RETURN
