page 77MARK-V FT-1000MP Operating Manual
REMOTE CONTROL OPERATION
Advanced Features
1. Contest Number Memory
The
[
#
]
key allows storage of a message of up to
20 characters in length. Within this message, a con-
test sequential serial number may be imbedded dur-
ing the programming process by sending “???” (three
Question Marks) in the place where the contest num-
ber is desired. The Question Marks should be sepa-
rated only by a letter space, not by a word space. Thus,
to send “5NN 001, 5NN 002,” and so forth, you send
“5NN ???” (not “5NN ? ? ?”) during memory storage.
A contest number may only be imbedded in the
memory location activated by [#] key.
You can manually increment or decrement the num-
ber (in case you need to repeat or “catch up” to the
correct contest number) by pushing the
[
#UP
]
key to
increment, or the
[
#DWN
]
key to decrement.
To reset an arbitrary contest number (in the middle
of the contest, when you may have been using a differ-
ent transceiver on a different band, for example), se-
lect menu selection 7-3. Now rotate the Main Dial to se-
lect the next-to-be-used contest number, and press
[
ENT
]
to save your new number and exit.
To abbreviate certain numbers in the contest ex-
change, select menu selection 7-6. In this Menu area,
substitutions of Morse letters for (longer) numbers can
be accomplished. For example, the keyer may be com-
manded to send “T” for “Zero,” “A” for “One,” “U” for
“Two,” and “N” for “Nine” while leaving all other num-
bers in their normal (longer) formats.
See the chart below for details of the selections
available.
To select between three-digit contest numbers (e.g.
“599001”) and four digit contest numbers (e.g.
“5991234”), select menu selection 7-6, then rotate the
Sub Dial to the final selection, which is the number of
playback digits. Select the desired number of digits,
then press
[
ENT
]
to save the setting and exit. Note
that, if you begin with a three-digit contest number, the
MARK-V FT-1000MP will automatically switch over to
four-digit numbering after QSO #999, so it generally is
best to select three-digit numbering.
2. CQ or ID Memory
The
[
ID
]
key allows storage and recall of any mes-
sage of up to 20 characters in length. Because of the
convenient location of
[
ID
]
key on the FH-1 Remote
Control Keypad option, this memory location is most
ideally suitable for your main “CQ TEST” message or
for your callsign (for one-touch use in a pile-up, for
example).
3. User Message Memories 1 - 4
Keys
[
CH 1
]
~
[
CH 4
]
allow storage and recall of
messages of up to 50 characters in length. These
memory locations are more suitable for longer mes-
sages which cannot be programmed into the “Contest
Number” or “ID” memory locations.
4. Message Storage
The
[
STO
]
key is used in the message memoriza-
tion process. Push
[
STO
]
followed by one of the mes-
sage playback keys (
[
#
]
,
[
ID
]
, or
[
CH 1
]
~
[
CH 4
]
), then
send (on your keyer paddle) the message to be stored,
then press the
[
STO
]
key to terminate the memory stor-
age process.
5. Message Monitor
(Playback without Transmitting)
The
[
MONI
]
key may be used to review the con-
tents of a memory location, or to determine the next-
to-be-used contest number, without transmitting the
message over the air.
To use this feature, the
[
MONI
]
key on the front panel
of the transceiver must be turned off. The reason for
this is that the
[
MONI
]
key activates the RF keying moni-
tor, which requires a transmitted signal in order to func-
tion.
To check the contents of the “ID” memory slot, for
example, press
[
MONI
]
then
[
ID
]
. You will hear the
message which currently is stored in the “ID” slot in
the speaker or headphones. To check to see what the
next-to-be-sent contest number is (in case you’ve for-
gotten, etc.), press
[
MONI
]
then
[
#
]
. The contents of
the “#” memory slot will be played (e.g. “599388 BK”),
and the contest number will not increment after play-
CONTECT NUMBER “CUT•EF ORMAT
MENU SELECTION “7-6”
Number
(
Standard Morse
)
Number
(
Cut Morse
)
0
1
2
3
5
7
8
9
“T”
“A”
“U”
“V”
“E”
“B”
“D”
“N”
– – – – –
•
– – – –
•
•
– – –
•
•
•
– –
•
•
•
•
•
– –
•
•
•
– – –
•
•
– – – –
•
–
ø
•
–
•
•
–
•
•
•
–
•
–
•
•
•
–
•
•
–
•
øThe standard Morse zero (0) can alternately be
sent as “O” ( – – – ).
Default
XXXX
4-Digit Contest Number Format
Truncated
XXX
Disabled
OFF
N/A
N/A
