78
Menu Contents
Chapter 7 Menus
TC SELECT [> TC select]: Determine which to display in the
time counter display, TC or VITC.
Note
TC is always displayed regardless the setting during the HDV
mode.
VITC [>> VITC]: Display VITC.
*TC [>> TC]: Display TC.
VITC [> VITC]: Determine whether to record the internally
generated timecode as VITC.
Note
This setting is invalid when the recording mode is in HDV
format.
OFF [>> OFF]: Do not record the internally generated
timecode as VITC. (VITC present in the input video signal
is recorded unchanged.)
*ON [>> ON]: Record the internally generated timecode as
VITC.
TCG REGEN [> TCG regen]: Select the signal to be
regenerated when the timecode generator is in the
regeneration mode (i.e., when the TC MODE menu item is
set to INT REGEN or EXT REGEN).
*TC & UB [>> TC & UB]: Both the timecode and user bit data
are regenerated.
TC [>> TC]: Only the timecode is regenerated.
UB [>> UB]: Only the user bit data are regenerated.
UB BINARY GP. [> Binary Gp.]: Select the user bit binary
group flag of the timecode generator.
Note
When the TC MODE menu item is set to EXT REGEN, the
user-bit binary group flag setting follows the setting on the
timecode input to this unit.
*000: NOT SPECIFIED [>> 000]: Character set not specified
001: ISO CHARACTER [>> 001]: 8-bit characters conforming
to ISO 646 and ISO 2022
010: UNASSIGNED-1 [>> 010]: Undefined
011: UNASSIGNED-2 [>> 011]: Undefined
100: UNASSIGNED-3 [>> 100]: Undefined
101: PAGE/LINE [>> 101]: Multiplex
110: UNASSIGNED-4 [>> 110]: Undefined
111: UNASSIGNED-5 [>> 111]: Undefined
VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the
VITC in.
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
from 12 to 20.
Factory default setting: *16 LINE [>> 16 line]
Notes
• You can insert the VITC signal in two places. To insert it in
two places, set both this item and also VITC POS SEL-2.
• The setting values are as follows when the system frequency
is set to 50i.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: *19 LINE [>> 19 line]
VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the
VITC in.
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
from 12 to 20.
Factory default setting: *18 LINE [>> 18 line]
Notes
• You can insert the VITC signal in two places. To insert it in
two places, set both this item and also VITC POS SEL-1.
• The setting values are as follows when the system frequency
is set to 50i.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: *21 LINE [>> 21 line]
VITC OUTPUT [> VITC out]: Select the timecode to be output
as VITC.
OFF [>> OFF]: Do not output VITC.
TC [>> TC]: Output TC after converting it into VITC.
*VITC [>> VITC]: Output VITC.
EE OUT PHASE [> EE out]: Determine the output phase for
the LTC signal output from the TC OUT connector when
recording timecode and in STOP REC mode (forced EE
mode).
*NO OUTPUT [>> NO OUT]: Suppress the output.
THROUGH [>> through]: Output the timecode input to the TC
IN connector as it is.
VIDEO INPUT PHASE [>> V input]: Output the timecode with
the same phase as the input video signal phase.
VIDEO OUTPUT PHASE [>> V output]: Output the timecode
with the same phase as the output video signal phase.
TIME CODE [Time code]: Settings related to the timecode
generator
Description of settings
